Skip to content

Special MetalsIndustrial FastenersGlobal Supply

DIN 125 Standard: Plain Washer Dimensions, Form A and Form B

DIN 125 is the German standard for metric plain (flat) washers: the disc that sits under a bolt head or nut to spread the clamping load over a wider area and protect the surface. It has two forms with identical dimensions. Form A has no chamfer and matches ISO 7089; Form B has a chamfered hole edge and matches ISO 7090. DIN 125 has since been replaced by DIN EN ISO 7089 and 7090, but the number still appears on drawings and purchase orders. 

To buy DIN 125 washers in carbon steel, A2 or A4 stainless steel, go to DIN 125 washers. For other DIN, ISO, ASME, IS and BS standards, see the Fastener Standards hub. 

DIN 125 at a glance

Item Detail
Standard DIN 125 Form A and Form B
Washer type Plain (flat) washer, normal series: outer diameter about twice the hole diameter
Size range in this table M1 to M100 (ISO 7089 and 7090 cover a narrower range, up to M64 
Form A No chamfer; ISO 7089
Form B Chamfered hole edge; ISO 7090
Replaced by DIN EN ISO 7089 (Form A) and DIN EN ISO 7090 (Form B) [VERIFY]
Steel hardness classes in ISO 7089 / 7090 200 HV and 300 HV  
Dimensions given d1 hole diameter (min), d2 outer diameter (max), s thickness, all in mm

DIN 125 Form A vs Form B

Form A Form B
Chamfer None Chamfered hole edge [VERIFY]
ISO equivalent ISO 7089 ISO 7090
d1, d2, s Same as Form B Same as Form A
Typical use Default plain washer under nuts and bolt heads Under bolt heads that have a radius under the head, where the chamfer clears it  
Other national equivalents CSN 21702, PN 82006, UNI 6592 CSN 21702, PN 82006, UNI 1751

DIN 125 Equivalent Standards

Standard Relationship to DIN 125
ISO 7089 (DIN EN ISO 7089) Equivalent of Form A; same dimensions
ISO 7090 (DIN EN ISO 7090) Equivalent of Form B; same dimensions
UNI 6592 / UNI 1751 Italian equivalents of Form A / Form B
CSN 21702, PN 82006 Czech and Polish equivalents, both forms
IS 2016 Indian plain washer standard; close for many sizes but not identical, so check the size against the table below  
ASME B18.22.1 Inch-series plain washers; different sizes, not interchangeable with DIN 125

DIN 125 dimensions, Form A and Form B (mm)

Sizes are for metric bolts and nuts. d1 is the hole diameter (minimum), d2 the outer diameter (maximum) and s the thickness. Form A and Form B share these values. For weight per 1,000 pieces, see the DIN 125 washers page. 

Size d1 min d2 max s
M1 1.1 3 0.3
M1.2 1.3 3.5 0.3
M1.4 1.5 4 0.3
M1.6 1.7 4 0.3
M1.7 1.8 4.5 0.3
M2 2.2 5 0.3
M2.5 2.7 6 0.5
M2.6 2.8 7 0.5
M3 3.2 7 0.5
M3.5 3.7 8 0.5
M4 4.3 9 0.8
M5 5.3 10 1
M6 6.4 12 1.6
M7 7.4 14 1.6
M8 8.4 16 1.6
M10 10.5 20 2
M12 13 24 2.5
M14 15 28 2.5
M16 17 30 3
M18 19 34 3
M20 21 37 3
M22 23 39 3
M24 25 44 4
M27 28 50 4
M30 31 56 4
M33 34 60 5
M36 37 66 5
M39 40 72 6
M42 43 78 7
M45 46 85 7
M48 50 92 8
M52 54 98 8
M56 58 105 9
M60 62 110 9
M64 66 115 9
M68 70 120 10
M72 74 125 10
M76 78 135 10
M80 82 140 12
M85 87 145 12
M90 93 160 12
M100 104 175 14

Fasteners and washers used with DIN 125

DIN 125 is normally paired with hex bolts and nuts from the same DIN family.  

Part DIN ISO equivalent
Hex bolt, partially threaded DIN 931 ISO 4014
Hex bolt, fully threaded DIN 933 ISO 4017
Hex nut DIN 934 ISO 4032
Socket head cap screw DIN 912 ISO 4762
Spring (split lock) washer, used with DIN 125 where locking is needed DIN 127 none
Plain washer, large series (outer diameter about three times the bolt diameter) DIN 9021 ISO 7093 
Plain washer, small series for cheese head and socket head screws DIN 433 ISO 7092 

Frequently Asked Questions

1. What is the difference between DIN 125 Form A and Form B?

Form A has no chamfer and Form B has a chamfered hole edge. Their d1, d2 and thickness values are identical. Form A matches ISO 7089 and Form B matches ISO 7090.

2. What is the ISO equivalent of DIN 125?

ISO 7089 for Form A and ISO 7090 for Form B. DIN 125 has been replaced by DIN EN ISO 7089 and 7090, and the common sizes carry the same dimensions.

3. What are the dimensions of a DIN 125 washer for M10?

Hole diameter d1 10.5 mm minimum, outer diameter d2 20 mm maximum and thickness s 2 mm.

4. Which bolts and nuts go with DIN 125 washers?

DIN 933 and DIN 931 hex bolts with DIN 934 hex nuts, which are ISO 4017, ISO 4014 and ISO 4032 in the ISO series.

5. How is DIN 125 different from DIN 9021?

DIN 9021 is the large series, with an outer diameter about three times the bolt diameter (30 mm against 20 mm for M10). It spreads the load further and suits soft material or oversize holes.

6. Is IS 2016 or ASME B18.22.1 the same as DIN 125?

No. IS 2016 is close for many sizes but not identical, and ASME B18.22.1 is an inch-series standard with different sizes. Check the size against the DIN 125 table before substituting.

Need DIN 125 washers in a specific material or size range? See our DIN 125 washers page or contact our technical team.

Worldwide Supplier

World Map
  • +91 9987685906
  • sales@jadealloys.com
Enquire Now
close slider

    Fill the form details and get a Free Quote

    Fill the Captcha